![]() ![]() Now, there is another piece of software by Logitech that's called G Hub. However, with the native macOS CoreAudio driver running in macOS on the M1 Mac, there is no way to update the firmware in the Yeti microphone. You can also make sure that the LogiGamingAudio driver is no longer running (by searching for its name). If you use this uninstall feature in the Blue app, it will remove itself properly, so after you reboot, you will be using the native macOS CoreAudio driver compiled for the Apple Silicon architecture, which can be seen in the "Kind" column of Activity Monitor when you search for CoreAudio. You will see the driver LogiGamingAudio running and if you enable the column "Kind" in Activity Monitor, you will see that the Kind of this driver is Intel.įortunately, the latest version of the Blue (Sherpa) app has an uninstall feature under the Blue menu in the macOS menu bar. You can see that by running the Activity Monitor app in macOS and doing a search in it for Logi. Therefore, it's safe to say that the Blue app functionality is broken in (at least) Ventura on (at least) M1 Mac.Īdditionally, please be advised that if you install the Blue app (aka Blue Sherpa), the driver loaded for the Yeti microphone is the Blue-compiled driver for the Intel architecture running in emulation on the M1 Macs. For the microphone to function, it has to be plugged in before macOS boots up, so once you upgrade the microphone software, you will have to reboot your Mac again. ![]() However, the Yeti microphone itself will not function at this point. There, you can check the microphone firmware version and update it from there. At this point, you will be able to click on the Microphone icon and go into the Microphone properties. So, is there a different way to update the software on Blue Yeti X without having to run G Hub or Blue Sherpa? Also, is there other software that can control additional features in the Blue Yeti X (like gain, noise reduction, gate, de-esser, compressor, equalizer, etc.).Īfter you install Blue Sherpa correctly, having given it the necessary permissions in System Preferences / System Settings (in Ventura) and rebooting macOs, you need to unplug the Blue Yeti microphone while Blue Sherpa is running and then plug it back in. I haven't tried Blue Sherpa myself in fear that I would have to spend hours trying to figure out how to uninstall it properly because it would cause some other artifact. I hear that Blue Sherpa (the original software made by Blue before Blue was sold to Logitech) requires that G Hub be installed. Additionally, the G Hub software installs the audio driver that is still compiled for the Intel architecture and is run in Rosetta 2 emulation, which is not optimal and should have been compiled for Apple Silicon now that it's been 2 years since M1 macs were first released. I believe the second device was probably the driver that was pumping the input through the G Hub software, while the first instance was the standard Apple driver that Blue Yeti X uses out of the box without any additional software. So, even though G Hub now works on M1 Macs in Ventura, and it sees the Blue Yeti X microphone, having duplicate Yeti devices in macOS is not something I am willing to deal with. Once that was done, and the Mac was rebooted once again, the duplicate devices named Yeti were gone. After googling the solution, I found a few sets of instructions as to how to fully uninstall the software. ![]() I figured it was caused by the G Hub software, so I tried to uninstall the G hub software and reboot the Mac, but the duplicate instances of Yeti audio input devices and Yet audio output devices persisted. Even though the microphone worked after installing the G Hub software and the software detected the Mic, after the installation of this software, my Mac (M1 Pro) started showing two instances of the Yeti device in audio inputs as well as two instances of the Yeti device in the audio outputs in macOS. Then, I decided to install the Logitech G Hub software to be able to gain additional control over the Blue Yeti X microphone as well as get sound effects (which are part of the G Hub) software. I bought a Blue Yeti X (Pro) microphone, and it was immediately properly detected in macOS Ventura 13.0.1.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |